come installare il firmware del dvd?
  • In diretta da GamesVillage.it
    • News
    • -
    • In Evidenza
    • -
    • Recensioni
    • -
    • RetroGaming
    • -
    • Anteprime
    • -
    • Video
    • -
    • Cinema

Visualizzazione risultati da 1 a 4 di 4

Discussione: come installare il firmware del dvd?

Cambio titolo
  1. #1
    Utente
    Registrato il
    05-03
    Località
    Messina
    Messaggi
    49.271

    come installare il firmware del dvd?

    ho scaricato il firmware aggiornato del mio dvd ma non ho capito come installarlo!le spiegazioni nel readme sono queste:

    ATAPI DVD-106 FIRMWARE UPGRADE 1.09
    This upgrade should NOT be applied to any other model DVD-ROM drive.

    Files:
    atpio109.hex : Firmware Version 1.09
    upg6a.exe : Upgrade Utility program
    up106.bat : Batch program to execute the upgrade.

    PROCEDURE
    1. Connect Pioneer DVD-ROM drive on the Secondary IDE Port with the drive set as Master (MA). Pioneer DOES NOT recommend using Cable Select (CS) NOR should there be a Slave (SL) device connected during the procedure.

    2. If Windows 95/98 is used, boot into MS-DOS mode by selecting the Start menu on Windows 95/98. If you are using Windows 2000 or ME you will need to make a DOS boot disk with the appropriate drivers or just use a Windows 98 bootdisk.

    3. Make sure there is no disc in the drive unit before the firmware upgrade is executed.

    4. Make note of where you unzipped the update files at , then go there and Execute the UP106.BAT file while you are in DOS (see point 2)

    5. The current version number of the firmware will be shown then erased and the new firmware will be uploaded.

    6. When the DOS prompt returns. Reboot the computer by powering OFF wait 10 seconds then power ON.

    Do not turn OFF the PC while upgrade is executed or the firmware upgrade will fail. Retry upgrade procedure from 4 through 6 if the firmware upgrade does fail.
    Apply power cycle (OFF/ON) if the firmware upgrade fails.

    IMPORTANT:
    The upgrade will not function and permanent failure of the drive could occur...IF it is interrupted in any way. OR if the wrong firmware is used. ALSO you must have the drive connected as per procedure point 1.


    qualcuno mi spiega chiaramente come fare??

  2. #2
    Riccardo90
    Ospite
    è tutto scritto:

    - devi aver messo il lettore sulla seconda porta ide come master (no slave, no cable select)

    - se hai win 98 parti in modalità dos, se hai 2000 (xp) devi creare un disco di avvio e partire da li.

    -levare ogni disco (tranne il floppy di avvio) dai lettori

    -ricordati dove hai estratto il firmware e vai nella cartella dove lo hai estratto (scrivendo: 'cd\CARTELLLAFIRMWARE' (senza virgolette))

    - scrivi UP106 (il .bat lo sottointende il dos quindi non occorre scriverlo)

    - quando ritorna al dos spegni il computer, aspetta una decina di secondi e riaccendilo.

    non spegnere il pc, se va via la corrente sei fottuto



    ti ho semplicemente tradotto in breve il testo da te postato (aggiungendo le frasi tra parentesi)

  3. #3
    Riccardo90
    Ospite
    dimenticavo, sei fottuto anche se hai scaricato un firmware sbagliato

  4. #4
    Utente
    Registrato il
    05-03
    Località
    Messina
    Messaggi
    49.271
    vabbe va troppo complicato e rischioso,lascio stare!cmq i firmware x il masterizzatore li ho scaricati ed installati da windows xp e non mi hanno dato problemi!ma questi x il lettore sono troppi complicati da fare!

Regole di Scrittura

  • Tu non puoi inviare nuove discussioni
  • Tu non puoi inviare risposte
  • Tu non puoi inviare allegati
  • Tu non puoi modificare i tuoi messaggi
  •